TM-9-2815-247-34P0001.gif
TM-9-2815-247-34P0002.gif
TM-9-2815-247-34P0003.gif
TM-9-2815-247-34P0004.gif
TM-9-2815-247-34P0005.gif

Tm-9-2815-252-24

• Chapter 1 Introduction
• Section Ii. Equipment Description And Data
• Figure 1-1. Engine Components
• Table 1-1. Equipment Data
• Section Iii. Preparation For Use
• Chapter 2 Operation
• Chapter 3 Maintenance
• Section Ii. Troubleshooting
• Table 3-2. Troubleshooting
• 4. Engine Hard To Start Or Will Not Start In Cold Weather
• 6. Engine Does Not Develop Full Power
• 7. Engine Overheating.
• 8. Excessive Oil Consumption.
• 11. Black Or Gray Smoke
• 12. Blue Exhaust Smoke.
• 14. Detonation Or Pre-Ignition
• Section Iii. General Maintenance
• 3-4. Disassembly And Assembly Sequence For Overhaul
• 3-4.2. Assembly
• 3-5. Crankcase Vacuum,
• Section Iv. Intake And Exhaust System Maintenance
• Figure 3-2. Intake Manifold
• Figure 3-3. Exhaust Manifold
• Thermostat
• Figure 3-4. Cooling System
• Waterpump
• Section Vi. Fuel System Maintenance
• Figure 3-5. Priming Fuel System
• Fuel Injection Pump
• Figure 3-7. Fuel Injection Pump, Fuel Filter, And Supply Lines
• Figure 3-8. Fuel Pump Tappet And Stud
• Table 3-3. Color Coded Shim Packs For Fuel Pump
• Figure 3-10. Checking Piston Drop
• Figure 3-11. Fuel Injector Pump Dimensions
• Fuel Supply Lines
• Fuel Injector
• Fuel Injector Cont.
• Figure 3-13. Fuel Infectors, Fuel Injector Pipes, And Fuel Return Line
• Fuel Injector Pipes And Fuel Return Line
• Fuel Solenoid
• Figure 3-14. Fuel Solenoid Installation
• Oil Filter And Crankcase Door
• Figure 3-15. Oil Filter And Crankcase Door
• Figure 3-16. Crankcase Door Fastener Tightening Sequence
• Figure 3-17. Strainer And Oil Pump
• Figure 3-18. Oil Pressure Test Setup
• Section Viii. Governor System Maintenance
• Figure 3-19. Governor System
• Figure 3-20. Governor Weights
• Long Loop Of Speeder Spring
• Section Ix. Electrical System Maintenance
• Figure 3-21. Starter Connection And Mounting Hardware
• Figure 3-22. Starter Assembly
• Figure 3-23. Starter Solenoid Test Circuit
• Figure 3-24. Solenoid Terminals
• Figure 3-25. Overrunning Clutch
• Figure 3-25. Overrunning Clutch Cont.
• Section X. Engine Subassembly Maintenance
• Figure 3-27. Cylinder Cover And Rocker Lever
• Cylinder Head Assembly
• Cylinder Head Assembly Cont.
• Figure 3-28. Cylinder Head Assembly
• Figure 3-29. Valve Guide Tool And Depth Stop
• Table 3-4. Cylinder Head Component Wear Limits
• Figure 3-30. Checking Cylinder Head Clearance
• Installation
• Gear Fnd Covfr\
• Figure 3-32. Gear End Cover
• Figure 3-33. Gear End Cover Capscrew Tightening Sequence
• Camshaft Assfmbly
• Table 3-5. Camshaft Component Wear Limits
• Figure 3-35. Measuring Gear Backlash And End Play
• Inspect And Measure
• Figure 3-36. Piston And Connecting Rod Assemblies
• Figure 3-37. Piston Ring And Gap Location
• Table 3-6. Piston And Connecting Rod Component Wear Limits
• Flywheel Housing
• Figure 3-38. Flywheel Housing
• Figure 3-39. Center Bearing Tube
• Figure 3-40. Crankshaft Assembly
• Figure 3-41. Main Bearing Tool
• Crankshaft
• Crankshaft Cont.
• Table 3-7. Crankshaft Component Wear Limits
• Crankcase Assembly
• Figure 3-43. Crankcase Assembly
• 3-34.3. Inspection.
• 3-34.4. Installation
• Appendix A References
• Appendix B Maintenance Allocation Chart
• B-3 Explanation Of Columns In The Mac
• B-4 Explanation Of Columns In Tool And Test Equipment Requirements
• Section Ii. Maintenance Allocation Chart For Diesel Engine Model Dn2m
• Maintenance Allocation Chart - Continued
• Maintenance Allocation Chart - Continued
• Maintenance Allocation Chart - Continued
• Section Iii. Tools And Test Equipment Requirements For Diesel Engine Model Dn2m
• Appendix C Expendable/Durable Supplies And Materials List
• Appendix D. Maintenance Procedure And Authorized Level Of Maintenance
• Section Iii. Maintenance Level To Paragraphs
• Appendix E Torque Chart
• Index
• Index - Continued
• Index - Continued
• Index - Continued
• Index - Continued
• The Metric System And Equivalents