TM  5-2815-241-34&P FUEL  PUMP  -  CONTINUED INITIAL  SETUP Tools Assembly   tool,   ST-419 Bit,   drill,   1/4-inch Bit,   drill,   11/64-inch Bit,   screwdriver,   flat-tip,   3/16-inch, 3/8-inch   drive Block,  support  (two  required) Chisel,   gouge,   1/2-inch Drill,   electric,   3/8-inch Driver,   ST-853 Gage,  bore Gage,  pressure,  oil  0  to  600  psi (0 to 4136 kPa) Gage,  thickness Goggles,  safety Hammer,   ball-peen,   16-ounce Hammer,  plastic-faced Handle,   ratchet,   3/8-inch   drive Handle,   ratchet,   1/2-inch   drive Key,  hex,  3/16-inch Key,  hex,  5/32-inch Mandrel Mandrel, seal driving Micrometer,  0-  to  1-inch Micrometer,  depth,  0-  to  1-inch Mittens,  cloth,  heat-protective Ohmmeter Pliers,  diagonal-cutting,  8-inch Pliers, slip-joint, 6-inch Pliers,   snapring Power  supply,  12  vdc Press,  arbor Puller,   ST-709 Puller,  dowel,  ST-667 Puller,  gear,  ST-1231 Punch,   center Punch,   driftpin,   brass,   3/16-inch Reamer Scale,  machinist’s,  6-inch Screwdriver,    flat-tip,    3/8-inch Screwdriver,    flat-tip,    1/4-inch Scribe,   machinist’s Socket,  3/16-inch  hex-head,  1/2- inch   drive Socket,   7/16-inch,   3/8-inch   drive Socket,   7/16-inch,   1/2-inch   drive Socket,   1/2-inch,   1/2-inch   drive V-blocks Vise,    soft-jawed Wrench,   box-end,   7/16-inch Tools  -  Continued Wrench,   open-end,   7/16-inch   (two   required) Wrench,   open-end,   1/2-inch Wrench,   open-end,   5/8-inch Wrench,   open-end,   15/16-inch Wrench,   open-end,   1-inch Wrench,  torque,  0  to  150  in.  lb  (0  to  16.9 Nlm),  3/8-inch  drive Wrench, torque, 0 to 150 ft lb (0 to 210 Nlm), 1/2-inch   drive Materials/Parts Cloth,  emery  (item  1,  appendix  B) Gasket,  fuel  pump  housing Gasket,   gear   pump Gasket, governor spring pack cover Grease,   extreme-pressure   (item   10, appendix   B) Key, coupling, front cover Lockwasher,  front  cover  (two  required) Lockwasher, fuel pump housing (seven required) Lockwasher,   gear   pump   (four   required) Lockwasher,  governor  spring  pack  cover (four    required) Lockwasher,  pulsation  damper  (six required) Lockwasher, shutdown valve (six required) Lockwasher,  throttle  lever  (two  required) Oil, lubricating (item 12, appendix B) Oil,  fuel  (item  11,  appendix  B) Seal, cap, fuel pump housing Packing,  preformed,  pulsation  damper  (two required) Packing, preformed, shutdown valve (two required) Packing,  preformed,  throttle  shaft  (two required) Packing,  preformed,  pulsation  damper (two   required) Packing,  preformed,  shutdown  valve Prussian  blue  (item  13,  appendix  B) Seal, oil, front cover (four required) Seal,  oil,  pulsation  damper Shaft,  shutdown  valve Tags,  marker  (item  17,  appendix  B) Washer,  nylon,  pulsation  damper Wire,  locking  (item  21,  appendix  B) 2-290